Search found 253 matches

by miked
25 Jun 2018, 12:53
Forum: Hispapanels / SimIO boards
Topic: next problem with the simio boards
Replies: 16
Views: 9685

Re: next problem with the simio boards

Hi Paul
My set up is as follows:
A raspberry 2 b is running raspbian (only by default!)with say an ip of 192.168.0.70 then I run a service called ser2net on this device. I can then plug 4 USB connected Arduinos (nano) running my own code. These act as IOCP servers (each with a different port # say 8110 - 8113). this IOCP address and ports are added to the IOCP drivers on the ProSim tab. The appropriate variables are assigned in the config tab (eg 2576 etc). The arduino looks for incoming data and acts upon it, reads switch states and sends them to prosim. This works very well. :D. So I'm writing code for 7 segment for the Chronometers.
by miked
25 Jun 2018, 08:57
Forum: Hispapanels / SimIO boards
Topic: next problem with the simio boards
Replies: 16
Views: 9685

Re: next problem with the simio boards

Hi
I am in the process of moving to native operation of my SimIO cards for Hispapanel Clocks. I assume the boards have to be plugged into the same computer as prosim (ie no network operation), Is this so?
If it is :twisted: then given the issues with reverse order and blanked digits I can't see the use for it. I will keep the clocks and write some simple Arduino code and use my "Raspberry Pi-USB Server" which I use for the Fire and Cargo Fire panels. :)
by miked
26 May 2018, 00:38
Forum: ProSimB738 - Technical support - software related
Topic: Issue with ProSim 2.05
Replies: 6
Views: 1101

Re: Issue with ProSim 2.05

Hi All
To reiterate, the issue is, that before version 2.05 update, all modules always updated automatically when opened the first time after Prosim was updated. So my question is, has this function been changed?
by miked
25 May 2018, 08:27
Forum: ProSimB738 - Technical support - software related
Topic: Issue with ProSim 2.05
Replies: 6
Views: 1101

Issue with ProSim 2.05

I have updated to version 2.05. However the various modules (Display, CDU etc) do not update when opened. All worked OK when going from 2.03 to 2.04. Has the update procedure changed?
by miked
12 Apr 2018, 01:30
Forum: FSX
Topic: Hardware Switch Detection
Replies: 3
Views: 1917

Re: Hardware Switch Detection

Hi
Your 'interface cards' report switch positions to Prosim. However some interface cards only send data when there is a "change of state" e.g.in your case parking brake "OFF" then back "ON" should show correct in P3D. This maybe your problem.
by miked
12 Apr 2018, 01:14
Forum: Opencockpits
Topic: Naive question ....
Replies: 4
Views: 1125

Re: Naive question ....

Hi
Does the yokebutton actually disengage the A/P? If so, then I believe the aural warning should stop when you press the button a second time.
by miked
04 Apr 2018, 01:24
Forum: ProSimB738 - General discussion
Topic: Pocket size Briefing Card
Replies: 3
Views: 894

Re: Pocket size Briefing Card

Hi Michael
Thanks for that.
by miked
03 Mar 2018, 01:56
Forum: ProSim737 User Projects
Topic: Flaps2Approach Website Update
Replies: 265
Views: 79781

Re: Flaps2Approach Website Update

Cheers willow
Thanks again :D
by miked
02 Mar 2018, 02:48
Forum: Hispapanels / SimIO boards
Topic: Rookie with 7 Segment Displays
Replies: 5
Views: 2720

Re: Rookie with 7 Segment Displays

Hi
As you may have seen ProSim version 2.02 has fixed this provides 6 digits for the comm radio displays. :D
by miked
27 Jan 2018, 07:27
Forum: ProSimB738 - Technical support - software related
Topic: Missing Display
Replies: 2
Views: 774

Re: Missing Display

Hi Jerry
You can turn it on in the 'Display' Tab in the Cockpit Setup section of the ProSim IOS

Go to advanced search